Installation

Trunk Lid Opener Cable/Fuel Fill Door Opener Cable Removal and Installation

Installation

SRS components are located in this area. Review the SRS component locations Locations and the precautions and procedures Service and Repair before doing repairs or service.

1. Trunk Lid/Fuel Fill Door Opener Cable





1. Install the trunk lid opener cable/fuel fill door opener cable (A) to the clips (B), and install the clips (C) securing the cable.

NOTE: Align the marks (D) with the clips as shown.





2. Install the grommet (A) to the fuel fill door latch (B).





3. Install the grommet (A) to the body.





4. Install the cushion tapes (A) and the clip (B) securing the trunk lid opener cable/fuel fill door opener cable (C).

NOTE: Align the marks (D) with the cushion tapes and the clip as shown.

2. Fuel Cap Adapter





1. Install the fuel cap adapter (A) into place.





2. Raise the fuel filler pipe (A), and install it to the fuel cap adapter (B).

3. Install the bolts (C).





4. Install the screw (A).

5. Install the fuel cap (B).

3. Fuel Pipe Protector





1. Install the fuel pipe protector (A).

4. Rear Wheel





1. Install the rear wheel.

NOTE: Before installing the wheel, clean the mating surfaces between the brake disc or the brake drum and the inside of the wheel.

5. Trunk Lid Latch




NOTE: Fix the original position of the outer end of the cable (A) on the trunk lid latch securely. And check the trunk lid latch operation: Make sure the trunk lid latch unlocks when pulling the trunk lid opener/fuel fill door opener. If necessary, adjust the position of the cable end.





1. Connect the trunk lid opener cable (A).





2. With trunk lid lock cylinder: Connect the cylinder rod (A).

3. Install the trunk lid latch (B).

4. Install the latch cover (C).

6. Trunk Lid Trim Panel





1. For some models: Install the trunk lid trim panel (A).

7. Trunk Side Trim Panel





1. Install the trunk side trim panel (A).

8. Trunk Rear Trim Panel





1. Install the trunk rear trim panel (A).

9. Trunk Lid Weatherstrip as Needed





1. Install the trunk lid weatherstrip (A).

10. Trunk Floor Cover





1. Install the trunk floor cover (A).





2. Install the front area of the trunk floor cover (A).

3. Raise the seat-back(s).

11. Both Rear Seat Side Bolsters





1. Install the rear seat side bolster (A).

2. The left side is shown; repeat on the right side.





3. Install the bolt (A) securing the rear seat side bolster (B).

4. The left side is shown; repeat on the right side.

12. Rear Seat Cushion





1. Install the hooks (A) to the rear seat cushion clips (B).





2. Install the bolt (A) securing the rear seat cushion (B).

13. B-Pillar Lower Trim





1. Install the B-pillar lower trim (A).

14. Front and Rear Door Opening Seals as Needed

Front





Rear





1. Install the front door opening seal (A) and the rear door opening seal (B).

15. Rear Door Sill Trim





1. While pulling up the rear seat cushion (A), install the rear door sill trim (B).

2. Push down the seat cushion, then install the hook (C) to the rear seat cushion clip (D).

16. Trunk Lid Opener/Fuel Fill Door Opener





1. Connect the trunk lid opener cable/fuel fill door opener cable (A) to the opener.





2. Install the opener mounting rear bolt (A) temporarily.

3. Install the opener mounting front bolt (B).





4. Install the front door sill trim (A).





5. Install the screw (A).

6. Tighten the opener mounting rear bolt (B).





7. Install the opener lock cylinder (A).

8. Install the cap (B) to the front door sill trim (C).