System Troubleshooting
Troubleshooting1. Turn the ignition switch ON (II) with a programmed key.
2. Check to see if the immobilizer indicator comes on.
Does the indicator come on?
YES - Go to step 3.
No - Go to step 12.
3. Check the immobilizer indicator operation.
Does the indicator come on for 2 seconds, then go off?
YES - Go to step 4.
No - Goto step 6.
4. Try to crank the engine.
Does the starter motor operate?
YES - Go to step 5.
No - Check the starter motor.
5. Try to start the engine. Does the engine start?
YES - If available, check the Status Log in the Immobilizer Info with the HDS. If the Status Log is not available, the immobilizer system is OK at this time.
No - Go to step 22.
6. Check to see if the immobilizer indicator comes on and blinks.
Does the indicator blink?
YES - Go to step 22.
No - Go to step 7.
7. Disconnect ECM connector A (32P).
8. Check to see if the immobilizer indicator goes off.
Does the indicator go off?
YES - Check the ECM.
No - Go to step 9.
9. Turn the ignition switch OFF.
10. Remove the gauge assembly and disconnect its connectors.
11. Check for continuity between ECM connector A (32P) No. 12 (IMOLMP) terminal and body ground.
Is there continuity?
YES - Repair a short in the wire.
No - Faulty immobilizer indicator, replace the gauge assembly.
12. Try to start the engine.
Does the engine start?
YES - Go to step 13.
No - Go to step 18.
13. Turn the ignition switch OFF.
14. Disconnect ECM connector A (32P).
15. Check for voltage between ECM connector A (32P) No. 12 terminal and body ground.
Is there battery voltage?
YES - Go to step 16.
No - Faulty No. 18 (7.5 A) fuse in the under-dash fuse/relay box. If the fuse is OK, check for an open in the wire between the ECM and under-dash fuse/relay box.
16. Remove the gauge assembly and disconnect its 30P connector.
17. Check for continuity between ECM connector A (32P) No. 12 (IMOLMP) terminal and gauge assembly connector A 30P) No. 22 terminal.
Is there continuity?
YES - Faulty immobilizer indicator, replace the gauge assembly.
No - Repair an open in the wire.
18. Turn the ignition switch OFF,
19. Disconnect the 5P connector from the immobilizer receiver unit.
20. Turn the ignition switch ON (II).
21. Check for voltage between the immobilizer receiver unit 5P connector No. 1 (IG1) terminal and body ground.
Is there battery voltage?
YES - Check the immobilizer receiver unit
No - Faulty No. 7 (15 A) fuse in the under-dash fuse/relay box. If the fuse is OK, check for an open in the wire between the immobilizer receiver unit and under-hood fuse/relay box.
22. Turn the ignition switch OFF.
23. Connect the HDS to the data link connector.
24. Turn the ignition switch ON (II).
25. Look at the System Check in the Immobilizer Info with the HDS.
Is the immobilizer system normal?
YES - Go to step 1.
No - Go to step 26.
26. Verify the System Check display on the HDS. Does the HDS display the following information?
- Harness short from the ECM to the immobilizer receiver unit. (S-net line short)
- The communication was not good between the ECM and the immobilizer receiver unit by the battery voltage low.
- The communication was not good between the ECM and the immobilizer receiver unit by influence of some noise.
- Immobilizer receiver unit failure
- ECM failure
YES - Go to step 27.
No - Go to step 31.
27. Turn the ignition switch OFF.
28. Disconnect the 5P connector from the immobilizer receiver unit.
29. Disconnect the ECM connector A (32P).
30. Check for continuity between the immobilizer receiver unit 5P connector No. 2 (IMOCD) terminal and body ground.
Is there continuity?
YES - Repair a short in the wire.
No - Substitute a known-good immobilizer receiver unit and/or ECM.
31. Verify the System Check display on the HDS.
Does the HDS display the following information?
- Blown fuse
- Harness open from the ECM to the immobilizer receiver unit.
- The communication was not good between the ECM and the immobilizer receiver unit by the battery voltage low.
- The communication was not good between the ECM and the immobilizer receiver unit by influence of some noise.
- Immobilizer receiver unit failure
- ECM failure
YES - Go to step 32.
No - Check the Possible Failures shown on the System Check display.
32. Turn the ignition switch OFF.
33. Disconnect the 5P connector from the immobilizer receiver unit.
34. Disconnect the ECM connector A (32P).
35. Check for continuity between the immobilizer receiver unit 5P connector No. 2 (IMOCD) terminal and ECM connector A (32P) No. 25 terminal.
Is there continuity?
YES - Substitute a known-good immobilizer receiver unit and/or ECM.
No - Repair an open in the wire.