Pinpoint Test E: The Restraints Control Module (RCM) Does Not Respond To The Scan Tool
Communications Network
Pinpoint Test E: The Restraints Control Module (RCM) Does Not Respond To The Scan Tool
Refer to Wiring Diagram Set 14, Module Communications Network for schematic and connector information. Diagrams By Number
Refer to Wiring Diagram Set 46, Supplemental Restraint System for schematic and connector information. Diagrams By Number
Normal Operation
The Restraints Control Module (RCM) communicates with the scan tool through the High Speed Controller Area Network (HS-CAN).
This pinpoint test is intended to diagnose the following:
- Fuse
- Wiring, terminals or connectors
- RCM
PINPOINT TEST E: THE RCM DOES NOT RESPOND TO THE SCAN TOOL
WARNING: Never disassemble or tamper with safety belt buckle/retractor pretensioners or adaptive load limiting retractors or probe the electrical connectors. Failure to follow this instruction may result in the accidental deployment of the safety belt pretensioners or adaptive load limiting retractors which increases the risk of serious personal injury or death.
WARNING: Never probe the electrical connectors on air bag, Safety Canopy(R) or side air curtain modules. Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
NOTE: The Supplemental Restraint System (SRS) must be fully operational and free of faults before releasing the vehicle to the customer.
NOTE: Most faults are due to connector and/or wiring concerns. Carry out a thorough inspection and verification before proceeding with the pinpoint test. Inspection and Verification
NOTE: Failure to disconnect the battery when instructed will result in false resistance readings. Refer to Battery, Mounting and Cables Battery Disconnect.
-------------------------------------------------
E1 CHECK THE RCM CONNECTION
- Ignition OFF.
- Depower the SRS. Refer to Supplemental Restraint System Supplemental Restraint System (SRS) Depowering and Repowering.
- Disconnect: RCM C310A.
- Disconnect: RCM C310B.
- Are RCM C310A pins 13 and 14 and RCM C310B pins 9 and 10 OK?
Yes
GO to E2.
No
REPAIR the RCM connector pins as necessary. REPOWER the SRS. REFER to Supplemental Restraint System Supplemental Restraint System (SRS) Depowering and Repowering. CLEAR the DTCs. REPEAT the network test with the scan tool.
-------------------------------------------------
E2 CHECK THE RCM VOLTAGE SUPPLY CIRCUIT FOR AN OPEN
- Deactivate the SRS. Refer to Supplemental Restraint System Supplemental Restraint System (SRS) Deactivation and Reactivation.
- Repower the SRS. Refer to Supplemental Restraint System Supplemental Restraint System (SRS) Depowering and Repowering.
- Ignition ON.
- Measure the voltage between the RCM C310A-13, circuit CBP20 (YE/VT), harness side and ground.
- Is the voltage greater than 10 volts?
Yes
GO to E3.
No
VERIFY the Central Junction Box (CJB) fuse 20 (10A) is OK. If OK, REPAIR the circuit. If not OK, REFER to the Wiring Diagrams to identify the possible causes of the circuit short. REACTIVATE the SRS. REFER to Supplemental Restraint System Supplemental Restraint System (SRS) Deactivation and Reactivation. CLEAR the DTCs. REPEAT the network test with the scan tool. Diagrams By Number
-------------------------------------------------
E3 CHECK THE RCM CASE GROUND
- Ignition OFF.
- Disconnect: Negative Battery Cable.
- Measure the resistance between the RCM C310A-14, circuit GD174 (BK/WH), harness side and ground.
- Is the resistance less than 5 ohms?
Yes
GO to E4.
No
REPAIR the circuit. REACTIVATE the SRS. REFER to Supplemental Restraint System Supplemental Restraint System (SRS) Deactivation and Reactivation. CLEAR the DTCs. REPEAT the network test with the scan tool.
-------------------------------------------------
E4 CHECK THE HS-CAN CIRCUITS BETWEEN THE RCM AND THE DLC FOR AN OPEN
- Measure the resistance between the RCM C310B-10, circuit VDB04 (WH/BU), harness side and the DLC C251-6, circuit VDB04 (WH/BU), harness side.
- Measure the resistance between the RCM C310B-9, circuit VDB05 (WH), harness side and the DLC C251-14, circuit VDB05 (WH), harness side.
- Are the resistances less than 5 ohms?
Yes
CONNECT the negative battery cable. GO to E5.
No
REPAIR the circuit in question. REACTIVATE the SRS. REFER to Supplemental Restraint System Supplemental Restraint System (SRS) Deactivation and Reactivation. CLEAR the DTCs. REPEAT the network test with the scan tool.
-------------------------------------------------
E5 CHECK FOR CORRECT RCM OPERATION
- Disconnect all the RCM connectors.
- Check for:
- corrosion
- damaged pins
- pushed-out pins
- Connect all the RCM connectors and make sure they seat correctly.
- Operate the system and verify the concern is still present.
- Is the concern still present?
Yes
INSTALL a new RCM. REACTIVATE the SRS. REFER to Supplemental Restraint System Supplemental Restraint System (SRS) Deactivation and Reactivation. CLEAR the DTCs. REPEAT the network test with the scan tool.
No
The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. REACTIVATE the SRS. REFER to Supplemental Restraint System Supplemental Restraint System (SRS) Deactivation and Reactivation. CLEAR the DTCs. REPEAT the network test with the scan tool.
-------------------------------------------------