No Response With a No Start Condition
NO RESPONSE WITH A NO START CONDITION
For a complete wiring diagram, refer to the Wiring Information Electrical Diagrams.
1. PCI BUS COMMUNICATION AND TEST FOR INTERMITTENT CONDITION
NOTE: The scan tool and cable must be operating properly for the results of this test to be valid.
1. Turn the ignition on.
NOTE: Ensure the IOD fuse is installed and battery voltage is between 10.0 and 16.0 volts.
2. With the scan tool, select ECU view.
NOTE: A red X will be next to the module that is not communicating or not installed on the vehicle, indicating that the module is not active on the Bus network. A green check indicates that the module is active on the Bus network.
Does the scan tool communicate with the Gateway module on the PCI Bus network?
Yes
- Go To 2
No
- Go To 3
2. VERIFY CAN C BUS COMMUNICATION
Does the scan tool communicate with the Powertrain Control Module (PCM) on the CAN C Bus circuit?
Yes
- Communications - Verbose Codes for further assistance on the loss of communication to the control modules that are not active on the Can C Bus.
No
- Refer to the CAN C BUS PERFORMANCE (GATEWAY MODULE) Diagnostic Procedure for further assistance. CAN C BUS Performance.
3. (D25) PCI BUS CIRCUIT OPEN AT THE DLC
1. Turn the ignition off.
2. Disconnect the negative battery cable.
3. Disconnect the scan tool from the DLC.
4. Disconnect the Gateway module harness connector.
5. Measure the resistance of the (D25) PCI Bus circuit between the DLC and the Gateway module harness connector.
Is the resistance below 5.0 ohms?
Yes
- Go To 4
No
- Repair the (D25) PCI Bus circuit for an open.
- Perform the BODY VERIFICATION TEST. Body Verification Test.
4. CHECK THE (D25) PCI BUS CIRCUIT FOR A SHORT TO VOLTAGE
1. Turn the ignition on.
2. Measure the voltage of the (D25) PCI Bus circuit at the DLC.
Is the voltage steadily above 7.0 volts?
Yes
- Go To 5
No
- Go To 6
5. (D25) PCI BUS CIRCUIT SHORTED TO VOLTAGE
NOTE: If the PCI Bus circuit is shorted to voltage the scan tool will be unable to identify the vehicle. Perform the test below, make the repairs as indicated. Re-attempt communication with the scan tool.
1. Turn the ignition off.
2. Using a voltmeter, connect one end to the (D25) PCI Bus circuit at the DLC and the other end to ground.
NOTE: For each module on the PCI Bus perform the following steps.
3. Turn the ignition off, wait one minute before disconnecting a module, turn the ignition on and check if the module disconnected was causing the short to voltage internally.
4. While monitoring the voltmeter, disconnect each module the vehicle is equipped with one at a time.
Is the voltage steadily above 7.0 volts with all the modules disconnected?
Yes
- Repair the (D25) PCI Bus circuit for a short to voltage.
- Perform the BODY VERIFICATION TEST. Body Verification Test.
No
- Replace the module that when disconnected eliminated the short to voltage.
- Perform the BODY VERIFICATION TEST. Body Verification Test.
6. (D25) PCI BUS CIRCUIT SHORTED TO GROUND
NOTE: If the PCI Bus circuit is shorted to ground the scan tool will be unable to identify the vehicle. Perform the test below, make the repairs as indicated.
1. Turn the ignition off.
2. Using a ohmmeter, connect one end to the (D25) PCI Bus circuit at the DLC and the other end to ground.
3. While monitoring the ohmmeter, disconnect each module the vehicle is equipped with one at a time.
NOTE: Total bus resistance to ground through all of the modules is typically between 350 to 1000 ohms. The more modules on the PCI Bus, the lower the total resistance will be.
Is the resistance below 150.0 ohms with all the modules disconnected?
Yes
- Repair the (D25) PCI Bus circuit for a short to ground.
- Perform the BODY VERIFICATION TEST. Body Verification Test.
No
- Replace the module that when disconnected the short to ground was eliminated.
- Perform the BODY VERIFICATION TEST. Body Verification Test.