Operation CHARM: Car repair manuals for everyone.
Hosted by mcallihan.com
Home >> Dodge >> 2009 >> Viper SRT-10 V10-8.4L >> Repair and Diagnosis >> A L L Diagnostic Trouble Codes ( DTC ) >> Testing and Inspection >> B Code Charts >> B1B8F

B1B8F






B1B8F-DRIVER SEAT TRACK POSITION SENSOR CIRCUIT OPEN





For a complete wiring diagram, refer to the Wiring Information Electrical Diagrams.

Theory of Operation

When powered, the CAN bus ignition status is IGN_RUN, and the Occupant Classification Module (OCM) is configured for a Driver Seat Track Position Sensor (STPS), the Occupant Classification Module (OCM) diagnoses the internal and external circuits to verify system performance. The fault occurs when the sensor circuit A/D feedback register is below the battery voltage limit but not shorted low (as specified by calibration) for 500 ms ± 110 ms.

- When Monitored:
When powered, the CAN Bus ignition status is in IGN_RUN, the module is configured for a Seat Track Position Sensor, and the module has successfully completed the shorted to ground test, the module checks the sensor circuit A/D feedback register for low voltage.

- Set Condition:
The fault occurs when the OCM sensor circuit A/D feedback register is below the battery voltage limit and above the shorted low limit for 500 ms ± 110 ms.





Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. Restraints System Pre-Diagnostic Procedure.

1. DETERMINE ACTIVE OR STORED DTC

Does the scan tool display active: B1B8F-DRIVER SEAT TRACK POSITION SENSOR CIRCUIT OPEN?

Yes

- Go To 2

No

- Perform the RESTRAINTS SYSTEM INTERMITTENT TEST. Restraints System Intermittent Test.

2. VERIFY SEAT POSITION SENSOR CIRCUITS





WARNING: Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

1. Disconnect the Driver Seat Track Position Sensor connector.
2. Measure the resistance between the (R261) Driver Seat Position Sensor Data circuit and the (R263) Driver Seat Position Sensor Voltage circuit at the Driver Seat Position Sensor connector.

Is the resistance below 10k ohms?

Yes

- Go To 6

No

- Go To 3

3. VERIFY OPEN SEAT POSITION SENSOR CIRCUITS





CAUTION: Disconnecting or connecting the OCM connectors with the battery connected permanently damages the OCM.

1. Disconnect the OCM C1 connector.
2. Measure the (R261) Driver Seat Position Sensor Data circuit resistance between the OCM C1 connector cavity 10 and the Driver Seat Track Position Sensor connector cavity 1.
3. Measure the (R263) Driver Seat Position Sensor Voltage circuit resistance between the OCM C1 connector cavity 9 and the Driver Seat Track Position Sensor connector cavity 2.

Is the resistance below 5.0 ohms on both circuits?

Yes

- Go To 9

No

- Go To 4

4. VERIFY DRIVER SEAT POSITION SENSOR PASSENGER SEAT WIRING




1. Disconnect the C311 body harness to Passenger Seat connector.
2. Measure the (R261) Driver Seat Position Sensor Data circuit resistance between the OCM C1 connector cavity 10 and the C311 (seat side) connector cavity 4.
3. Measure the (R263) Driver Seat Position Sensor Voltage circuit resistance between the OCM C1 connector cavity 9 and the C311 (seat side) connector cavity 3.

Is the resistance below 5.0 ohms on both circuits?

Yes

- NOTE: Do not attempt to repair the seat wiring.

- Replace the Passenger seat wiring.
- Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Restraints System Verification Test.

No

- Go To 5

5. VERIFY DRIVER SEAT POSITION SENSOR BODY WIRING




1. Disconnect the C310 body harness to Driver Seat connector.
2. Measure the (R261) Driver Seat Position Sensor Data circuit resistance between the C311 (body side) connector cavity 4 and the C310 (body side) connector cavity 1.
3. Measure the (R263) Driver Seat Position Sensor Voltage circuit resistance between the C311 (body side) connector cavity 3 and the C310 (body side) connector cavity 2.

Is the resistance below 5.0 ohms on both circuits?

Yes

- NOTE: Do not attempt to repair the body wiring.

- Replace the body wiring harness between the C311 (body side) connector and C310 (body side) connector.
- Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Restraints System Verification Test.

No

- NOTE: Do not attempt to repair the seat wiring.

- Replace the Driver Seat wiring harness.
- Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Restraints System Verification Test.

6. VERIFY SEAT POSITION SENSOR CIRCUITS





CAUTION: Disconnecting or connecting the OCM connectors with the battery connected permanently damages the OCM.

1. Disconnect the OCM C1 connector.
2. Measure the resistance between the (R261) Driver Seat Position Sensor Data circuit and the (R263) Driver Seat Position Sensor Voltage circuit at the Driver Seat Position Sensor connector.

Is the resistance below 10k ohms?

Yes

- Go To 7

No

- WARNING: If the Occupant Classification Module (OCM) is dropped at any time, it must be replaced. Failure to take the proper precautions could result in accidental airbag deployment and serious or fatal injury.

- Replace the OCM.
- Perform the OCM REZERO. Testing and Inspection.

7. VERIFY SEAT POSITION SENSOR CIRCUITS




1. Disconnect the C311 Body Harness to Passenger Seat connector.
2. Measure the resistance between the (R261) Driver Seat Position Sensor Data circuit and the (R263) Driver Seat Position Sensor Voltage circuit at the Driver Seat Position Sensor connector.

Is the resistance below 10k ohms?

Yes

- Go To 8

No

- NOTE: Do not attempt to repair the seat wiring.

- Replace the Passenger seat wiring.
- Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Restraints System Verification Test.

8. VERIFY SEAT POSITION SENSOR CIRCUITS




1. Disconnect the C310 Body Harness to Driver Seat connector.
2. Measure the resistance between the (R261) Driver Seat Position Sensor Data circuit and the (R263) Driver Seat Position Sensor Voltage circuit at the Driver Seat Position Sensor connector.

Is the resistance below 10k ohms?

Yes

- NOTE: Do not attempt to repair the seat wiring.

- Replace the Driver Seat wiring.
- Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Restraints System Verification Test.

No

- NOTE: Do not attempt to repair the seat wiring.

- Replace the Body Harness between the Driver Seat C311 connector and Passenger Seat C310.
- Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Restraints System Verification Test.

9. CHECK OPERATION OF THE DRIVER SEAT TRACK POSITION SENSOR
1. Replace the Driver Seat Track Position Sensor.
2. Reconnect all disconnected components except the battery.

WARNING: Turn the ignition on, then reconnect the 12-volt battery. Failure to follow these instructions may result in possible serious or fatal injury.

3. Connect the scan tool to the Data Link Connector - use the most current software available.
4. Use the scan tool and erase all codes in the OCM.
5. Turn the Ignition Off, and wait 15 seconds before turning the Ignition On.
6. Wait one minute, and read active codes.

Did the active B1B8F-DRIVER SEAT TRACK POSITION SENSOR CIRCUIT OPEN DTC return?

Yes

- WARNING: If the Occupant Classification Module (OCM) is dropped at any time, it must be replaced. Failure to take the proper precautions can result in accidental airbag deployment and serious or fatal injury.

- WARNING: Turn the ignition off, disconnect the 12-volt battery and wait two minutes before proceeding. Failure to follow these instructions may result in possible serious or fatal injury.

- CAUTION: Disconnecting or connecting the OCM connectors with the battery connected permanently damages the OCM.

- Replace the OCM.
- Perform the OCM REZERO. Testing and Inspection.

No

- Repair is complete.
- Perform the RESTRAINTS SYSTEM VERIFICATION TEST. Restraints System Verification Test.

pro multis · About Operation CHARM