Differential Carrier Assembly Disassemble (8.25 Inch Axle Lock Tab Style)

Differential Carrier Assembly Disassemble (8.25 Inch Axle Lock Tab Style)

Tools Required
* J 22912-B Split-Plate Bearing Puller
* J 2619-01 Slide Hammer
* J 29369-1 Bushing and Bearing Remover
* J 34011 Pilot Bearing Remover
* J 36598 Holding Fixture
* J 36599-A Side Bearing Nut Wrench
* J 45765 Pinion Remover
* J-45858 Front Axle Bearing Race Remover/Installer - 8.25 Inch Axle
* J 8614-01 Flange and Pulley Holding Tool

Inspection Procedure

Perform the following before disassembling the axle:

1. Remove the drain plug from the axle.
2. Drain the axle lubricant.
3. Inspect the oil and the case for metal chips.
Determine the source of the metal chips, such as a broken gear or bearing cage.
4. Check the ring gear backlash. Refer to Backlash Inspection and Adjustment.

This information can be used in order to determine the cause of the axle problem. The information will also help when setting up and preloading the differential case.

Determine the cause of the axle problem before disassembly, if possible.

Disassembly Procedure

1. Install the differential carrier assembly in a vise.




2. Remove the front axle actuator, S4WD axle only.




3. Remove the inner axle shaft bearing and the inner axle shaft seal by performing the following steps:

1. Install the J 29369-1 (1) behind the inner axle shaft bearing.
2. Install the J 2619-01 (2) to the J 29369-1 (1).
3. Using the J 2619-01, remove the inner axle shaft bearing and the seal.

4. Disconnect the right side inner axle shaft from the differential side gear using a hammer and a brass drift, F4WD axle only.
5. Remove the inner axle shaft, F4WD axle only.
6. Remove the inner axle shaft housing to differential carrier assembly bolts.
7. Remove the inner axle shaft housing, F4WD axle only.




8. Carefully remove the inner axle shaft housing with the inner axle shaft and clutch fork components from the differential carrier assembly, S4WD axle only.




9. Remove the inner axle housing bolt (1), axle shaft housing (2), and gasket (3).




10. Remove the following components from the inner axle shaft housing, S4WD axle only:

1. The clutch fork inner spring (10)
2. The clutch fork assembly (11)
3. The clutch shaft shim (9)
4. The clutch shaft sleeve (8)
5. The front drive axle clutch gear (6) by doing the following:

1. Clamp the inner axle shaft housing (4) in a vise.
Clamp only on the mounting flange.
2. Strike the inside surface of the shaft (1) flange with a hammer and a brass drift in order to dislodge the front drive axle clutch gear (6) from the inner axle shaft (1).

6. Remove the front drive axle clutch gear (6)
7. Remove the thrust washer (5)
8. Remove the inner axle shaft (1)




11. Remove the inner axle shaft bearing and the inner axle shaft seal by performing the following steps:

1. Place the differential carrier assembly into a vise.
Clamp only on the mounting flange of the differential carrier assembly case.
2. Install the J 29369-1 (1) behind the inner axle shaft bearing.
3. Install the J 2619-01 (2) to the J 29369-1.
4. Using the J 2619-01, remove the inner axle shaft bearing and the inner axle shaft seal.

12. Remove the differential carrier assembly from the vise.
13. Remove the front drive axle clutch shaft.




14. Using the J 34011, remove the clutch shaft bearing.




15. Remove the vent connector.




16. Remove the differential carrier assembly bolts (1).
17. Separate the left carrier case half from the right carrier case half (2) by tapping on the on the carrier case with a hammer and a brass drift.
18. Remove the differential carrier housing (2) and the differential carrier housing gasket (3).
19. Remove the differential case assembly.
Disconnect the differential bearing adjuster nut locks from the differential bearing adjuster nut by prying up on the locks.




20. Remove the differential bearing adjuster nuts and the differential bearing cups by doing the following:

1. Install the J 36599-A onto the differential bearing adjuster nut.
2. Turn the J 36599-A clockwise in order to push the differential bearing adjuster nut and the bearing cup out of the bore.

21. Remove the differential bearing adjuster nut sleeves using a hammer and brass drift.




22. Install the J 8614-01 as shown.
Remove the pinion nut while holding the J 8614-01.
23. Remove the washer.




24. Install the J 8614-2 (2) and the J 8614-3 (3) into the J 8614-01 (1) as shown.
25. Remove the pinion yoke by turning the J 8614-3 (3) clockwise while holding the J 8614-01 (1).
26. The steps below explain how to remove the drive pinion and pinion bearing cups using the J 36598 or the J 45765 and the J-45858. Follow the appropriate steps depending on what tool is available.
27. Install the J 36598 into a vise.




28. Install the left differential carrier case half onto the J 36598 and the J 36598-6.
29. While holding the forcing screw of the J 36598, turn the handle of the J 36598 counterclockwise in order to remove the pinion with the following components:

* The pinion gear selectable shim
* The inner pinion bearing
* The collapsible spacer




30. Install the J 36598-5 (3) behind the inner pinion bearing cup.
31. Thread the forcing screw of the J 36598 (1) onto the J 36598-5 (3) until fully seated.
32. While holding the forcing screw of the J 36598 (1), turn the handle of the J 36598 (2) counterclockwise and press the inner bearing cup out from the differential carrier case.




33. Install the J 36598-5 (2) behind the outer pinion bearing cup.
34. Install the forcing screw of the J 36598 (1) to the J 36598-5 (2).
35. While holding the forcing screw of the J 36598, turn the handle of the J 36598 clockwise in order to remove the following components:

* The pinion oil seal
* The pinion outer bearing
* The pinion outer bearing cup




36. Install the J 45765 to the left side differential carrier case half over the drive pinion as shown.
37. Turn the forcing screw of the J 45765 clockwise to remove the following components from the left side differential carrier case half:

* The drive pinion gear
* The pinion gear selectable shim
* The inner pinion bearing
* The collapsible spacer

38. Remove the drive pinion seal using a suitable seal remover.
39. Remove the outer pinion bearing from the differential carrier case half.




40. Install the J 45858-4 over the inner pinion bearing cup.




41. Install the forcing screw (1) of the J 45858 into the J 45858-4 (2).
42. Drive out the inner pinion bearing cup by pounding on the forcing screw with a hammer.




43. Install the J 45858-3 (3), the thrust bearing and the washer (2), and the forcing screw (1) over the outer pinion bearing cup bore.




44. Install the J 45858-5 into the pinion bearing bore behind the outer pinion bearing cup.
Slowly turn the forcing screw clockwise until the J 45858-5 is evenly seated behind the outer pinion bearing cup bore and the J 45858-3 is evenly seated over the outer pinion bearing cup bore.
45. Remove the outer pinion bearing cup by turning the forcing screw clockwise.
46. Remove the collapsible spacer from the drive pinion.




47. Install the J 22912-B between the pinion bearing and the drive pinion.
48. Using the J 22912-B and a hydraulic press, remove the inner pinion bearing
49. Remove the pinion gear selectable shim.