Front Differential Case, Actuator
Tools Required^ J 24319-B Universal Steering Linkage Puller
^ J 37780 Axle Shaft Remover
^ J 3289-21 Holding Fixture
^ J 37769 Differential Holding Fixture Adapters
^ J 3289-20 Holding Fixture Base
^ J 22888-D Side Bearing Remover
^ J 8107-4 Differential Side Bearing Remover Plug
^ J 37758 Pinion Outer Race Installer
^ J 8092 Driver Handle
^ J 24433 Side Bearing Installer
1. Raise and suitably support the vehicle. Refer to the General Information sub-section in the Service Manual.
2. Remove the 4 bolts and the front skid plate from the vehicle, if equipped.
3. Place a drain pan or suitable container under the front axle assembly.
4. Remove the front axle housing drain plug (2) and drain the front axle oil.
5. Remove the right front wheel.
6. Disconnect the right side front wheel speed sensor electrical connector.
7. Remove the right side front wheel speed sensor retaining bolt (2) and sensor (3) from the steering knuckle.
8. Remove the right outer tie rod lock nut.
9. Separate the right outer tie rod from the steering knuckle using the J 24319-B.
10. Remove the 6 bolts (2) and the flange (1).
11. Remove the drive axle shaft snap ring (2).
12. Remove the drive axle shaft spindle washer (1) from the drive axle shaft.
13. Remove the caliper bolts and caliper from mounting bracket and set aside.
14. Remove the right and left stabilizer shaft link nuts (1). Remove stabilizer shaft and bushings from the control arms.
15. Use a hydraulic jack in order to support the right control arm.
16. Remove the right strut bracket to steering knuckle bolts (1) and nuts (2).
17. Remove the right ball joint lock nut.
18. Use the J 24319-B in order to separate the lower control ball joint from the knuckle.
19. Remove the right steering knuckle/hub assembly.
20. While lowering the hydraulic jack, remove the coil spring.
21. Remove the right side drive axle from the front differential housing using the J 37780. If the right side drive axle does not separate from the differential housing using J 37780, extend the length of J 37780 using a pipe to provide more leverage to get the axle shaft retaining ring past the differential gear. The retaining ring may break during the axle shaft removal.
22. On the left drive axle, make a reference mark (2) on the following components in order to ensure correct installation.
^ The inner drive axle flange (1).
^ The differential side joint flange (3) of the drive axle shaft.
23. Remove the left side drive axle flange bolts and position drive axle aside.
24. Disconnect the vent hoses from the front axle housing.
25. Remove the front propeller shaft to front axle bolts.
26. Remove the front propeller shaft.
27. Remove the front differential rear mount nuts and bolts (1).
28. Remove the mount (2).
29. Support the front differential for removal.
30. Remove the front differential to the right side mount bolts.
31. Remove the front differential to the left side mount bolts.
32. Lower the front differential with assistants.
33. Remove the left side output shaft axle from the differential housing.
34. Remove the 6 differential carrier bolts and the two reamer bolts from the front axle housing.
35. Install the J 3289~21 to the differential carrier with the J 37769.
36. Place the differential carrier and the holding fixture into the J 3289-20.
37. Inscribe alignment marks on the differential side bearing caps to ensure proper assembly.
38. Remove the 2 bolts (1) and the side bearing lock plates (3) from the differential carrier.
39. Remove the differential inner air hose (8).
40. Remove the 4 bolts (2) and the side bearing caps (1) from the differential carrier.
41. Remove the side bearing adjusters from the differential carrier.
Important:
If during the right side drive axle removal, the retaining ring breaks, be sure to remove any material that may have fallen into the differential carrier.
42. Remove the differential ring gear and the case from the differential
carrier.
43. Remove the side bearings (1) from the differential case using the J 22888-D with the J 8107-4.
44. Remove the actuator.
45. Remove the 10 bolts and the ring gear from the differential case.
Important:
Apply P/N 12345493 (in Canada, use P/N 10953488), or equivalent, to the threaded portion of each ring gear bolt being installed into the differential case.
46. Install the ring gear (2) to the differential case. Secure with 10 bolts (1).
Tighten
Tighten the ring gear bolts to 85 Nm (63 lb ft).
47. Install the actuator to the differential case assembly.
48. Install the side bearing (1) on the left side of the differential case assembly (2) using the J 37758 with the J 8092. Place the differential case assembly on the hydraulic press.
Use the J 37758 with the J 8092 in order to place the left differential side bearing on the left differential case with the tapered side up and slowly press the left differential side bearing onto the left differential case.
49. Install the side bearing (1) on the right side of the differential case assembly (2) using the J 24433 with the J 8092 and J 8107-4. Place the differential case assembly on the hydraulic press using the J 8107-4 for support and to protect the left differential side bearing.
Use the J 24433 with the J 8092 in order to place the right differential side bearing on the right differential case with the tapered side up and slowly press the right differential side bearing onto the right differential case.
50. Install the differential case assembly into the differential carrier.
51. Install both side bearing adjusters (2) on the side bearing races.
52. Install both side bearing caps onto the differential carrier and secure with the four side bearing cap bolts.
Tighten
Tighten the differential side bearing cap bolts to 15 Nm (11 lb ft).
53. Perform the differential side bearing preload adjustment using the procedure listed below.
54. Perform the backlash inspection and adjustment using the procedure listed below.
55. Install the differential inner air hose.
56. Install the side bearing lock plates and the 2 bolts to the differential carrier.
Tighten
Tighten the side bearing lock plate bolts to 13 Nm (10 lb ft).
57. Remove the holding fixture and adapters from the differential carrier.
58. Apply RTV silicone sealer P/N 1052917, or equivalent, to the differential carrier mating surface on the front axle housing.
59. Install the differential carrier (1) into the front axle housing (2).
60. Install the 6 differential carrier bolts and the two reamer bolts.
Tighten
Tighten the differential carrier bolts to 23 Nm (17 lb ft).
61. Install the left side output shaft axle to the differential housing.
62. Raise the front differential housing with assistants and support with a suitable hydraulic jack.
63. Install the front differential mount to left mounting bolts.
Tighten
Tighten the bolts to 50 Nm (37 lb ft).
64. Install the front differential mount to right mounting bolts.
Tighten
Tighten the bolts to 50 Nm (37 lb ft).
65. Remove the hydraulic jack from supporting the front differential housing.
66. Install the front differential rear mount and the nuts and bolts.
Tighten
Tighten the front differential rear mount bolts and nuts to 50 Nm (37 lb ft).
67. Install the front propeller shaft and bolts.
Tighten
Tighten the propeller shaft bolts to 50 Nm (37 lb ft).
68. Connect the vent hoses.
69. Install the differential side joint flange of the drive axle shaft to the inner axle shaft flange.
Be sure to align the reference marks on the inner axle shaft flange and the differential side joint flange of the drive axle shaft.
70. Secure the flange bolts and nuts.
Tighten
Tighten the differential side joint bolts and nuts to 55 Nm (41 lb ft).
71. Install the new retaining ring and right drive axle shaft to the differential housing.
72. Use a hydraulic jack in order to support the front control arm.
73. Install the right steering knuckle/hub assembly.
74. Install the lower control ball joint to the knuckle.
75. Install the new right ball joint lock nut.
Tighten
Tighten the nut to 60 Nm (43 lb ft).
76. Install the right strut bracket to steering knuckle bolts and nuts.
Tighten
Tighten the nuts and the bolts to 95 Nm (69 lb ft).
77. Remove the hydraulic jack.
78. Install the left and right stabilizer shaft and bushing to the control arm. Install the stabilizer shaft link nuts.
Tighten
Tighten the link nuts to 29 Nm (21 lb ft).
79. Install the caliper and bolts to the mounting bracket.
Tighten
Tighten the bolts to 27 Nm (20 lb ft).
80. Install the drive axle shaft spindle washer onto the drive axle shaft.
81. Install the drive axle shaft snap ring onto the end of the drive axle.
82. Apply RTV silicone sealant, P/N 1052366, or equivalent, to the flange.
83. Install the 6 flange bolts.
Tighten
Tighten the flange bolts to 48 Nm (35 lb ft).
84. Install the right outer tie rod end to the steering knuckle and the new lock nut.
Tighten
Tighten the nut to 43 Nm (31 lb ft).
85. Install the front wheel speed sensor to the steering knuckle.
86. Install the retaining bolt.
Tighten
Tighten the bolt to 7.8 Nm (69 lb in).
87. Connect the front wheel speed sensor electrical connector.
88. Install the right front wheel.
89. Install the front axle housing drain plug into the front axle housing.
Tighten
Tighten the drain plug to 23 Nm (17 lb ft).
90. Remove the front axle housing oil level/filler plug from the front axle housing.
91. Refill the front axle housing with approximately 1 liter (1 qt) of 80W-90 GL5 lubricant, P/N 12345977 (in Canada, use P/N 10953482), or equivalent.
92. Install the front axle housing oil level/filler plug into the front axle housing.
Tighten
Tighten the oil level/filler plug to 40 Nm (30 lb ft).
93. If the vehicle is equipped with an engine skid plate, install the front skid plate to the vehicle. Secure the skid plate with 4 bolts.
Tighten
Tighten the skid plate bolts to 54 Nm (40 lb ft).
94. Lower the vehicle.