P0430
Diagnostic Chart:
Electrical:
CIRCUIT DESCRIPTION
In order to control emissions of Hydrocarbons (HC), Carbon Monoxide (CO) and Oxides of Nitrogen (NOx), a three-way catalytic converter is used. The catalyst within the converter promotes a chemical reaction which oxidizes the HC and CO present in the exhaust gas, converting them into harmless water vapor and carbon dioxide. The catalyst also reduces NOx, converting it to nitrogen. The VCM has the capability to monitor this process using HO2S 2. HO2S 2, located in the exhaust stream past the three-way catalytic converter, produces an output signal which indicates the oxygen storage capacity of the catalyst; this in turn indicates the catalyst [prime]s ability to convert exhaust emissions effectively. If the catalyst is functioning correctly, the HO2S 2 signal will be far less active than that produced by HO2S 1. If a problem exists which causes the VCM to detect excessive HO2S 2 activity outside of an acceptable range for an extended period of time, the VCM will set DTC P0430, indicating that the three-way catalytic converter's oxygen storage capacity is below a threshold considered acceptable.
CONDITIONS FOR SETTING THE DTC
^ No VS sensor DTCs
^ No AIR DTCs
^ No CAM DTCs
^ No PRNDL/Transmission DTCs
^ No TP sensor DTCs
^ No HO2S DTCs
^ No Misfire DTCs
^ No MAP sensor DTCs
^ No Fuel Trim DTCs
^ No IAT sensor DTCs
^ No ECT sensor DTCs
^ No MAF sensor DTCs
^ No EGR DTCs
^ No AIR DTCs
^ No EVAP DTCs
^ The vehicle is in a Closed Loop fuel control
^ Engine speed is greater than or equal to 900 rpm for at least 35 seconds
^ Engine run time is greater than 6 minutes
Test Enable
^ Catalyst temp is greater than or equal to 475°C
^ Closed Loop
^ Baro pressure is greater than or equal to 73 kPa
^ IAT is greater than -6.75°C but less than 73°C
^ Engine idling for less than 60 seconds
ACTION TAKEN WHEN THE DTC SETS
The VCM will turn ON the Malfunction Indicator Lamp (MIL).
CONDITIONS FOR CLEARING THE MIL/DTC
^ The VCM turns the MIL OFF after 3 consecutive drive trips when the test has Run and Passed and not Failed.
^ A history DTC will clear it no fault conditions have been detected for 40 warm-up cycles (coolant temperature has risen 22°C (40°F) from the startup coolant temperature and the engine coolant temperature exceeds 70°C (160°F) during the same ignition cycle).
^ Use the scan tool Clear Information function.
^ Disconnect the VCM battery feed for 30 seconds.
DIAGNOSTIC AIDS
Difficulty running the OBD II status DTC P0430 test may be encountered in areas where test conditions cannot be maintained easily, especially in urban areas. To minimize the amount of driving required to complete the test, use the following procedure:
^ Catalyst can be warmed up in service bay previous to drive cycle.
^ Engine also can be warmed up in bay also. HO2S 2 activity test: Using a scan tool, monitor MAP, HO2S 1, and HO2S 2 displays in Park or Neutral above idle. Compare HO2S 1 and HO2S 2 activity (amplitude and frequency) to each other during a 30 second period. If HO2S 2 activity is nearly as great as HO2S 1 activity, a problem exists; use diagnostic table. If much less activity is noted, system is functioning properly.
TEST DESCRIPTION
Number(s) below refer to the step number(s) on the Diagnostic Table.
2. This table includes checks for conditions that can cause the three-way catalytic converter efficiency to appear degraded. Inspect and repair exhaust system as necessary per Exhaust System. Also inspect the HO2S 2 pigtail and engine harness for any damage that can cause an intermittent fault in HO2S 2 sensor signal HIGH and LOW circuits.
3. If the three-way catalytic converter needs to be replaced, make sure that another condition is not present which caused the catalyst to be damaged. These conditions include a) misfire; b) high engine oil consumption or coolant consumption; c) retarded spark timing or weak spark. To avoid damaging the replacement three-way catalytic converter, correct engine misfire or mechanical fault before replacing three-way catalytic converter.