Convertible Top Stowage Cover

Figure 10-9-21 - Allante Phase II Convertible Top Stowage Cover:

GENERAL DESCRIPTION

Figure 10-9-21 The Phase II convertible top stowage cover is now a hinged unit that is closed by simply pushing down on the front of the cover. There are no longer any rollers or guides required.

Figure 10-9-22 - Stowage Cover and Hinge Mounting:

REMOVAL AND INSTALLATION

Figure 10-9-22

Remove or Disconnect

1. Hard top or lower convertible top, if necessary. Refer to "Hard Top" or "Convertible Top" in this Section.
2. Raise stowage cover (1) by pulling lever marked "COVER OPEN" located behind and to the left of driver's seat.
3. Mark position of hinge strap (4) in relation to cover.

4. Bolts and washers (5), while a helper holds the cover.
5. Stowage cover (1), with the aid of a helper.

Install or Connect

1. With the aid of a helper, position cover (1) to the holes in hinge straps (4).
2. Bolts and washers (5), but DO NOT TIGHTEN.
3. Align cover with scribe marks previously made.
4. Tighten bolts (5).
5. Check for proper operation. Adjust if necessary.

HINGES

Figure 10-9-22

Remove or Disconnect

1. Hard top or lower convertible top, if necessary. Refer to "Hard Top" or "Convertible Top" in this Section.
2. Stowage cover (1). Refer to "Stowage Cover" in this section.

Important

Do not allow rear compartment lid to raise fully. It could contact hinges and be damaged.
3. Raise rear compartment lid (2) partially, being careful not to allow it to touch hinges (4).
4. Screws (7) from rear compartment front upper carpet (6).
ALLANTE HARD TOP AND CONVERTIBLE TOP 10-9-13

10-9-14 HARD TOP AND CONVERTIBLE TOP ALLANTE

5. Lift carpet to gain access to hinge bolts (3). Mark position of hinge, hinge washers, and bolts.
6. Hinge bolts and hinge.

Reinstall or Connect

1. Position hinge (4) to scribe marks previously made.
2. Hinge bolts (3) and washers.
3. Screws (7) to rear compartment front upper carpet (6).
4. Close rear compartment lid (2).
5. Stowage cover (1).
6. Check for proper operation. Adjust if necessary.

Figure 10-9-23 - Safety Belt Retractor Cover:

SAFETY BELT RETRACTOR COVER

Figure 10-9-23

Remove or Disconnect

1. Hard top or lower convertible top. Refer to "Hard Top" or "Convertible Top" in this Section.
2. Raise stowage cover by pulling lever marked "COVER OPEN" located behind drivers seat.
3. Two screws (3) and lift retractor cover (1) away from vehicle.
4. To remove from safety belt, turn over, remove two phillips screws (4) and retaining strap (5), then feed belt through slot (6).

Reinstall or Connect

1. If removed from belt, feed through slot (6), and attach retaining strap (5) with two phillips screws (4).
2. Position retractor cover (1) and two screws (2).
3. Close stowage cover and check for alignment. Adjust if necessary.

ADJUSTMENTS

To move rear of stowage cover up or down:
1. The stowage cover should be flush with quarter panel and rear compartment filler panel.
2. With the cover closed, loosen hinge bolts. Refer to "Hinge" in this Section. Adjust only one side at a time.
3. Position cover as indicated in step one and tighten bolts.
4. Repeat for opposite side, if necessary.

To move stowage cover fore and aft:
1. The latch should be centered in its striker and cover should be flush with safety belt retractor covers when closed.
2. Open cover, and loosen bolts holding hinge strap to cover. Refer to "Convertible Top Stowage Cover" in this Section. Adjust only one side at a time.

3. Position cover as indicated in step one and tighten bolts.
4. Repeat for opposite side, if necessary.

To move rear of retractor cover up or down:
1. The retractor cover, proper adjustment, should be flush with stowage cover when it is closed.
2. Loosen rear bracket. Refer to "Safety Belt Retractor Cover" in this Section.
3. Move cover up or down as indicated in step one.
4. Tighten bolt. Repeat for opposite side, if necessary.